How to Connect Your MP3 Player or iPod to Your Stereo System

By Doug Aamoth January 7, Q: Without spending a fortune, is there a way I can connect my phone to the stereo so I can listen to music? Yes, you absolutely have a few options — some more expensive than others, and one that might actually cost you next to nothing. That thing is looong gone by now, right? For a couple sawbucks, you can add a Bluetooth connection of sorts to your stereo. Your phone connects to the transmitter via Bluetooth, and the transmitter then relays the audio from your phone to a blank FM station on your radio. Several of these products feature microphones so you can make and take hands-free calls as well.

Will my car amp power my speakers and subwoofer?

This makes the GTO19t an ideal tweeter upgrade for systems powered with head-unit or factory amplifier power, or even with many of the GTO Series amplifier combinations to help keep up with systems that feature one or more subwoofers. Three-ohm voice coils Three-ohm voice coils in the GTO 19t stand-alone tweeter compensate for the added resistance by thin factory-speaker wiring and provide more output than other tweeter components of the same class.

Frequency response up to 21kHz A wide frequency response that extends beyond 20kHz helps compensate for speaker placement variations in your car and human hearing deficiencies in the high-frequency spectrum above 15kHz.

Mar 04,  · I made this because It was hard for me to figure out how to do. So I figured others would have trouble. Heres a video of me explaining how to hook up car speakers in your room to an amplifier.

You can go used, in which case it really depends on what’s out there for sale: Amps, receivers, AVR’s all would be fine. As long as you’re not expecting ear bleeding loudness, this should be a good little amp to get. It’s single RCA inputs, so for you you’d use your 3. When you use this method, when you first hook everything up, turn the volume all the way down on both the amp and on the sub, also set the crossover on the sub to Hz.

Once you’ve done that, turn up the volume on the amp until the speakers are playing as a reasonable level. Next slowly turn up the sub until it matches the speakers to your liking. Now, start lowering the crossover level you may also need to adjust the sub’s volume level as you go , Hz is about where you’ll want to stop but if there’s a point higher where it sounds the best leave it there. I wouldn’t really go any lower than 70Hz as the sub will handle the lower frequencies better at louder levels.

If you find something with bass management let me know and I’ll help out with that. Share RockyPlays October 5, 2: Pricing aside, what is the best amp I could get with this sub and speakers.

Off-Grid Party Sound Systems

Subwoofer Setup Part I: Placement and positioning While a subwoofer’s deep bass is nondirectional, it would be unwise to just stick the sub anywhere that’s convenient in your room. Corner placement is the de facto strategy for most people, possibly because the sub will then be out of the way and almost always produces the most bass, but corner placement may not yield the most accurate bass, or smoothest transition to the speakers. The sub and speakers have to work together as a team, and ideally you should never hear the sub as a separate sound source.

If you want to run two speakers off each of your amp’s four channels, eight speakers total, then yes, you can do that using two 9-conductor cables connecting the amp to the vehicle harness. Just connect two speakers, left dash and door speakers, for example, to each amplifier output terminal.

How do you hook up an amp? Make sure that the power wire and aux cable are on opposite sides of the vehicle for less distortion and interference. MORE What is the difference between a 2 channel and 4 channel amp? You will need what is called an L. It is used to convert speaker lines into an RCA output. If it’s running so hot you can’t touch it, in most cases it will be due to either the way the speakers are hooked up or the impedence of the speakers. You can incresse the resistance to the amp to have it run cooler by connecting speakers in series or getting speakers with a higher ohm rating.

Running a subwoofer with a stereo amp (no sub output)

In some ways, thick, high-end wire can present MORE of a problem than the conventional skinnier stuff. More on that later. For the purposes of discussion we will use the term “amp” short for amplifier to refer to any receiver, integrated amp or power amp. This sheet is intended for solid state, transistorized sets.

Hooking up a 4 channel amp to your front and rear speakers takes some work and time, but it’s a great way to get sound you’ll love. Considering buying an amplifier? You can find some great 4 channel amps (including the Alpine MRV-F pictured here) in my 4 channel amp buyer’s guide.

Bass speaker High frequency horn speaker Crossovers handle the separation of sound frequencies, and handle their distribution to speakers. Passive crossovers built into speakers’ cabinets are used in compact music systems. Active crossovers are separate components, and are connected between the sound source a mixer or preamp , and the amplifier. In professional audio applications, two amplifiers are used to create a bi-amped system. The sound source creates the overall sound signal, and the crossover filters and separates the frequencies.

The frequencies are sent to dedicated amplifiers, which are connected to dedicated speakers. Plug a standard shielded connection cable into the mixer’s main output. Consult your owner’s manual or manufacturer’s Web site for specific information. Plug the other end of the connection cable into the crossover’s input jack.

Learn How To Install A Car Radio

They have two separate speakers that emit different ranges of sounds. The woofer, or the larger speaker, emits the lower to mid range frequencies. The tweeter, the small speaker, covers the high range frequencies and noises.

The amount of space you have to work with will help determine the size amp you buy. A common place to fit an amp is in the trunk or luggage compartment of your car.

Choosing speakers Choosing speakers Whether you are fitting four new speakers, or just adding an extra pair to your existing system, the choice is vast. Below are some old speakers and fader controls from Pioneer. A TS-VX is a surface-mounted wedge-type rear speaker. B TS-R mounts into the rear parcel shelf. C TS-X30 is a surface-mounted rear speaker. D TS flush-mounted speaker for use in front or rear locations. E AD fader control. F UD A fader control.

The standard twin-speaker car stereo system has one obvious drawback. If you mount the speakers on the rear shelf, to hear the sound clearly you often have to turn up the volume to a level that is too loud for the rear seat passengers. Conversely, if the speakers are fitted at the front of the car – and they are usually low down in the door panels – the sound in the back can be muffled by the seats. All-round sound The solution to this problem is to fit a four-speaker system, with two speakers mounted in the front and two in the rear.

For the front of the car you will probably find that the door panels are the best, if not the only, location available, though some cars have speaker positions built into each side of the dash. In the rear of the car you can again mount the speakers in the doors or the side panels on a two-door car , or on or under the parcel shelf.

One-Wire Alternators: Are They Better Or Just Easier To Hook up?

Most receivers have either preamp-in and preamp-out connections or tape monitor connections. In most cases, these are the best way to connect an equalizer to your stereo. Connecting to the tape monitor channels will require connection to only your receiver. Learn how to hook up an equalizer to the receiver instead.

Learn how to properly wire speakers to a receiver or amplifier using spring clips or binding posts with bare, pin, spade, or banana plug connectors. Understand the Easy Ways to Hook up Most Any Kind of Subwoofer. Make Wiring Stereos a Breeze by Using Speaker Wire Connectors.

In this article we look at some of the practical ways of wiring four speakers to each amplifier left and right. For example, it is normal to have your main HiFi amplifier in the lounge room. It is also common to want to have some speakers in the family room, outside patio or pool area and in the workshop or garage. If you need to connect just 2 pair of speakers to a HiFi stereo amplifier that is, 2 speakers to 1 amp , see my article on How to connect 2 speakers to 1 amplifier.

I have had many people over the years tell me it is easy to connect multiple speakers — all you have to do is wire the speakers in series. In the following diagrams I will only show the wiring for one side of a stereo amplifier, lets says the left side of the stereo. In reality this wiring needs to be duplicated for the right side speakers too. Four speakers wired in parallel This diagram shows how to wire four speakers in parallel.

It is the same as wiring each speaker directly from the amplifier, like this: Wiring speakers in parallel is not a good way of connecting three, four or more HiFi speakers as it puts too much load on the amplifier as explained in earlier article Four speakers wired in series This diagram shows how to wire four speakers in series.

How To Connect Amplifier To Receiver?

How to Install a Car Audio Amplifier and Subwoofer by braniac This article will provide a better working knowledge of car audio components and outline how to successfully install them. First, under the hood of your vehicle, disconnect the cable from the Negative – terminal of the battery. This will prevent any accidental short circuits from happening while installing your amplifier. Locate an area under the hood where you can mount your fuse holder.

Jul 03,  · if i wanted to hook up my car speakers (which are stock) to an amp (its a 4 channel), would i just instead of running the car speaker wires to the head unit, just attach a longer speaker wire to the car speaker wires and hook that up to the it that simple? and i have a after market head unit so it show more if i Status: Resolved.

Just what is tone? What is a good tone and how do you achieve it? Which amps you should choose for your setup and how to get the tones you want. We also looked at the importance of choosing the right guitar — not only for your technique and rig but also for inspiration to play and create music. Check out part 1 and part 2. Amps People tend to prioritize guitars and a bunch of pedals and forget the importance of a good sounding amp.

Choosing the right amp for your setup is crucial for getting the tones you want from your guitar and pedals. I strongly suggest that you buy a guitar and amp before you spend all your savings on pedals. This will ensure the best fundament for your tones and playing. A tube amp consist of a pre-amp section that takes the small signal from your guitar and amplifies it enough to drive the power amp section. Most amps allow you to manipulate the pre-amp signal with a number of gain and EQ controls.

4 Channel Amp Install and Speaker Swap – Amplified #144